- Temperature ranges: RT to 250°C
- Maximum mould dimension: width x length x thickness (450 X 450 X 100)mm

- Temperature ranges: RT (no liquid cooling system)
- Maximum mould dimension: width x length x thickness (600 x 600 x 100)mm

- Temperature ranges: RT to 450°C
- Maximum mould dimension: width x length x thickness (250 x 250 x 100)mm

- Available sieve size: 0.5 mesh, 1.0 mesh 1.5 mesh and 2.0 mesh.
- Materials accepted: natural fiber and some synthetic fibre.

- Maximum sample dimension: width x length x thickness (250 x 250 x 5)mm.
- Accuracy: ±0.1mm.
- Materials accepted: polymer composites and plastic sheets.

- 240 V~, 50 Hz, 1240 W, 13000 rpm.
- Maximum sample thickness: 25mm.
- Materials accepted: polymer composites and plastic sheets.

• Tensile test:
  - Load cell available: 20kN & 50kN
  - Grip type for flat samples; plastics, polymer composites, soft metal.
  - Sample thickness range for 20kN load cell: (0 to 7)mm
  - Sample thickness range for 50kN load cell: (0 to 21)mm
  - Testing speed range: (0.1 to 500)mm/min

• 3-point bending:-
  - Load cell available: 20kN
  - Flat sample types of plastics, polymer composites, soft metal.
  - Maximum support span (L/2): 100mm
  - Testing speed range: (0.1 to 50)mm/min

• Compression test:
  - Load cell available: 20kN & 50kN
  - Flat sample types of plastics, polymer composites, soft metal.
  - Maximum compression platen radius: 100mm
  - Maximum sample height: 140mm

- Several impactor types and radius
- Minimum dart impact weight: 3.29kg
- Maximum speed: 72km/h
- Maximum dart weight: Please contact us
- Adjustment: Height, speed, energy of impact
- Maximum sample size: width x length x thickness (5 x 5 x 5[Depend on the type of material])cm
- Materials accepted: polymer composites, plastic sheets and soft metal.

- Temperature ranges: (RT to 1000)°C
- Heating rate ranges: (0.001K/min to 50K/min)
- Cooling rate ranges: Not available
- Testing environment: Nitrogen gas
- Sample weight ranges: (5 to 20)mg
- Crucible: aluminium pan/ alumina pan

- Temperature ranges: (-150 to 600)°C
- Heating rate ranges: (0.001K/min to 50K/min)
- Cooling rate ranges: (0.001K/min to 50K/min)
- Testing environment: Nitrogen gas
- Sample weight ranges: (5 to 20)mg
- Crucible: close lid aluminium pan

- Maximum sample size: width x depth x thickness (1.5 x 1.5 x 1.5)cm
- Maximum magnification: 18000X with 2000X digital
- Voltage: 5kV electron (fixed)

- Transmitted and reflected capability
- System: Polarizer & differential interference contrast (DIC) (reflected mode)
- Objective magnification: 5X, 10X, 20X & 50X
- Digital image capturing (CCD camera) and analysis software

- Temperature sweep: (RT to 100)°C
- Sample performance test (3hrs at elevated temperature)
- Variable heater power (Watt)
- Sample dimension: width x length x thickness (5 x 5 x [0.5 or 1])cm

- Sample dimension: 14.5 cm X 2 cm X 0.3 cm (length X width X thickness) with 0.5cm holes will be drilled at both sample end.
- Initial load: 1.322 kg (13.22N)
- Additional load available: 10N, 15N, 20N, 30N, 40N, 50N, 60N, 70N, 80N, 90N and 100N
- Test temperature range (thermal chamber): 30°C until 90°C
- Suitable material for testing: Thermoplastic, thermosets and polymer composites
- Strain sensitivity: 0.01mm
- Data capture and plotting: Manual read from the machine

- Range of sample weight: (100 – 300)g
- Accuracy: ±0.001g/cm3

- Infrared heating element.
- Maximum heating temperature: 200°C
- Moisture detection accuracy: ±0.1%
- Range of sample weight: (100-400)g